The Solera 17' Black Fade RV Awning Roller and Fabric (Std) # LCV000211498 you asked about comes with the fabric and the roller tube. It does not come with the rail extrusion like # LC715217 to mount the awning fabric to the side of the RV. If you are installing a new rail extrusion, the LaSalle Bristol XTRM Butyl Tape - 45' L x 1-1/2" W - Qty 1 # 344270341411-1 and Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc # FA1131822 are my recommendation.
Many RV's will already have this installed... view full answer...
The replacement Top Tube Pad For the Hull-A-Port Carrier, part # 8537418 comes with 2 pieces in the package.
There is a foam pad similar to pipe insulation that has a slit and slips over the upright tube on the carrier. Then there is a piece of fabric with Velcro that fits over the pad. view full answer...
I am not sure where you saw that the Solera 10' Replacement Awning Fabric # LCV000334346 was 11 foot wide but it for sure is 10 foot. If you wanted an 11 foot version you'd instead want the part # LCV000334344. view full answer...
Yes. All Solera awning fabric replacements like the # LCV000334341 come with the spot for a poly cord to be installed the length of the awning, which allows you to slide the light strip holder on and install your LED lights. You will want to save the poly cord and the plastic mounting strip to install on the new fabric since those parts are not included. view full answer...
The part # PE5113901 does not come with the top bar. It comes with the top fabric, the rear window, and plastic and adhesive strips. view full answer...
The weatherstrip on the Solera 14' Replacement Awning Fabric - Sand Fade w/ White Weatherstrip # LCV000334376 is the black section closest to the trailer that you see in the linked installation video. Basically the closer part of the awning takes the most stress when it comes to rain and such to this part is thicker and more durable than the rest of the awning to deal with this extra stress. It also helps to protect the awning fabric when it's rolled up in the stored position. view full answer...
The Bestop SuperTop, part # B5159504 will work well for your 1967 CJ-5.
This top comes with all of the fabric, buckles, fittings and the webbing needed to install it on your Jeep. This covers the front seats only and is made of mildew and UV-resistant fabric. view full answer...
The Brake Mounting Flanges part # 4-44-1 that you referenced are sold individually. If you needed a pair you would need to order a quantity of 2.
Be sure to have a qualified fabricator with experience in installing flanges install them. view full answer...
The Solera Classic Universal Awning Support Arms part # LC434718 come with everything shown in the photos on our product page including support arms, torsion springs, and hardware. The only thing that would be needed for a complete awning is the roller tube and fabric. view full answer...
The Draw-Tite # 75155 you were looking at uses M12x1.25 bolts for the front three holes, and M8x1.25 for the hole closest to the front of the vehicle.
With that said you'll want to have a fabrication verify that the way you're installing the hitch is correct as in the OEM vehicles the frame is not threaded, but instead has nuts welded on the inside of the frame that the bolts go into. The frame is not thick enough nor strong enough to thread and install the bolts into without those nuts. view full answer...
Lippert part # LC351825 is a set of replacement arms, crank heads, crank rod and fasteners. The crank heads have mounting brackets which are shown in the linked photo.
This kit does not include the awning rail # LC715217 that mounts to the side of the RV nor the awning fabric/roller like # LCV000231492. view full answer...
The Rampage Replacement Upper Door Skins, part # RA89715 do have the windows included with the skin.
The windows have a zipper that runs around 3 sides and allows you to unzip them and store them in the pockets on the lower part of the door. These skins are made of a factory-grade Black Denim fabric. view full answer...
The Solera Awning and Roller part # LCV000211457 only comes with the fabric and the roller. It does not come with any hardware beyond that.
You will need the Solera Manual Pull Style Awning Drive Head # LC271181
Solera Manual Pull Style Awning Idler Head # LC272397
Solera Manual Awning Pull Strap # LC292794
Solera 63" Short Awning Support Arm # LC97UD view full answer...
The Solera Slider Topper awnings like # LCV000168110 come complete with mounting hardware, as well as the awning rail. The hardware hole pattern is universal and will match most competitive brands.
To be sure you are ordering the correct Solera Slider, select the fabric size that extends no less than 2-1/2-inches beyond each side of your slide box width (a total of at least 5-inches longer than the slider box).
This awning unit is made in the USA. view full answer...
The hardware kit for your 2011 Lexus RX 350 has been discontinued by Aries. I do have a list of the hardware that you can source locally.
2- 12mm Lock Washers
2- 12mm Hex Nuts
2- 12mm Oversize Hex Nuts
2- 12mm ID x 35mm OD x 3mm Flat Washers
2- 8-1.00mm x 25mm Hex Bolts
2- 8-1.25mm x 40mm Hex Bolts
8- 16 mm Lock Washers
8- 8mm ID x 22m OD x 3mm Flat Washers
The two 12-1.75mm x 60mm Bolt Plates, two 12-1.75mm x 120mm Bolt Plate and two 8mm Nut Plate will not be able to be sourced locally... view full answer...
Even though we do not carry a replacement hardware kit for this Westin Ultimate Bull Bar with Skid Plate, part # 32-1695, I can tell you what the contents of a hardware kit would most likely include.
I pulled the installation instructions for this product and found that you would need the following to install this product on your 2007 Ford F150:
2 BRACKET, PASSENGER AND DRIVER
4 M12- 1.75 X 30MM HEX HEAD BOLT
8 M12 FLAT WASHER
4 M12 LOCK WASHER
4 M12 HEX NUT
4 M12-1.25 X 30MM HEX HEAD... view full answer...
The BulletProof Hitches Adjustable 2-Ball Mount part # MD206 does not come with a hitch pin as that is how it is offered from the manufacturer. It will accept a standard hitch pin like part # PC3 but I recommend protecting your investment with locking hitch pins part # 34061674-D or just part # 34061074-D. view full answer...
The Draw-Tite # 36071 does not come with a ball mount but it does come with a hitch pin and clip to secure the drawbar to your trailer hitch.
For a hitch ball you can use part # 19256 for a 1-7/8" hitch ball or part # 19258 for a 2" hitch ball. Their individual prices can be found on their product pages. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11296, for the 2005 Ford Focus Wagon comes with the mounting hardware, but it does NOT come with a ball mount.
The ball mount you will need for the Curt hitch is the Draw-Tite Ball Mount, part # 3592. It must be used in the rise position only. It will include the pin and clip.
If you are towing with this hitch you will also need the following items.
Tow Ready 2 Inch Hitch Ball, part # 19258, or Tow Ready 1-7/8 Inch... view full answer...
The Curt Class IV 2 Inch Hitch, part # 14301, will include all of the mounting hardware. I am including a link to the installation instructions of the Curt hitch.
If you will be towing with this hitch on your 2007 Chevrolet Silverado New Body you will also need to purchase the following items.
Draw-Tite Ball Mount, part # 40331
Hidden Hitch Pin And Clip, part # PC3
Curt 2 Inch Hitch Ball, part # A-90, or Tow Ready 2-5/16 Inch Hitch Ball, part # 19286
Pollak Twist-in, 7-Pole, RV-Style... view full answer...
Go To Results